Παραγωγή πέλλετ (pellets) για ιδιόχρηση
- stratis 1
- Αποσυνδεμένος
- Platinum Member
Before useing this machine the die should be breaking-in as follows: Prepare 5kg raw
materials and 1kg silver sand, then mixed them sufficiently and inject 1kg used oil. Start
the machine and put in all the mixed materials. Then adjust the pressing roll bolt until it
outputs normally. (Caution: the adjusted gap cannot be too small, if not the pressing roll or
die will be damaged.) Keep the machine working for an hour for materials. Then put in
normal raw materials and begin to produce. If the machine cannot work regularly, fine-tune
the bolt a little loose until it can work.
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.
- osakis
- Αποσυνδεμένος
- Senior Member
- Δημοσιεύσεις: 71
- Ληφθείσες Ευχαριστίες 11
stratis 1 έγραψε: 2. Breaking-in of the new die:
Before useing this machine the die should be breaking-in as follows: Prepare 5kg raw
materials and 1kg silver sand, then mixed them sufficiently and inject 1kg used oil. Start
the machine and put in all the mixed materials. Then adjust the pressing roll bolt until it
outputs normally. (Caution: the adjusted gap cannot be too small, if not the pressing roll or
die will be damaged.) Keep the machine working for an hour for materials. Then put in
normal raw materials and begin to produce. If the machine cannot work regularly, fine-tune
the bolt a little loose until it can work.
Τι ήθελε άραγε να πει ο ποιητής?
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.
- stratis 1
- Αποσυνδεμένος
- Platinum Member
osakis έγραψε:
stratis 1 έγραψε: 2. Breaking-in of the new die:
Before useing this machine the die should be breaking-in as follows: Prepare 5kg raw
materials and 1kg silver sand, then mixed them sufficiently and inject 1kg used oil. Start
the machine and put in all the mixed materials. Then adjust the pressing roll bolt until it
outputs normally. (Caution: the adjusted gap cannot be too small, if not the pressing roll or
die will be damaged.) Keep the machine working for an hour for materials. Then put in
normal raw materials and begin to produce. If the machine cannot work regularly, fine-tune
the bolt a little loose until it can work.
Τι ήθελε άραγε να πει ο ποιητής?
Για να στρωσει το μηχανημα θελει 5 κιλα ακατεργαστο υλικο (πριονιδι)+1κιλο αμμο(εγω εβαλα απο παραλια αφου την έπλυνα με νερο βρυσης για ναφυγει το αλατι)+λαδι χρησιμοποιημενο (εγω εβαλα τριανταρι ορυκτελαιο αυτο που βαζω και στο ξυλοκοφτικο) .
Το υλικο αυτο πρεπει να περασει απο τη μηχανη πολλες φορες για μια ωρα.
Μετα ριχτε κανονικο υλικο.
Αν δεν βγαινει πελλετ ρυθμιστε τα μπουλονια ποιο χαλαρα.
Αν εχετε αδυνατα νευρα φωναχτε δυνατα 他妈的 中国
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.
- xrysafis72
- Αποσυνδεμένος
- Platinum Member
- Δημοσιεύσεις: 641
- Ληφθείσες Ευχαριστίες 64
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.
- DIMITRIS38
- Αποσυνδεμένος
- Elite Member
- Δημοσιεύσεις: 211
- Ληφθείσες Ευχαριστίες 31
fuzzy logic 2 p15kw
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.
- antisakis
- Συντάκτης θέματος
- Αποσυνδεμένος
- Platinum Member
- Δημοσιεύσεις: 531
- Ληφθείσες Ευχαριστίες 35
Τι ήθελε άραγε να πει ο ποιητής?
Για να στρωσει το μηχανημα θελει 5 κιλα ακατεργαστο υλικο (πριονιδι)+1κιλο αμμο(εγω εβαλα απο παραλια αφου την έπλυνα με νερο βρυσης για ναφυγει το αλατι)+λαδι χρησιμοποιημενο (εγω εβαλα τριανταρι ορυκτελαιο αυτο που βαζω και στο ξυλοκοφτικο) .
Το υλικο αυτο πρεπει να περασει απο τη μηχανη πολλες φορες για μια ωρα.
Μετα ριχτε κανονικο υλικο.
Αν δεν βγαινει πελλετ ρυθμιστε τα μπουλονια ποιο χαλαρα.
Αν εχετε αδυνατα νευρα φωναχτε δυνατα 他妈的 中国
Τελικα πελλετ εβγαλες με την παραπανω συνταγη;
Παρακαλούμε Σύνδεση ή Δημιουργία λογαριασμού για να συμμετάσχετε στη συζήτηση.